CNC-machined alu nut that holds front lower molded lower suspension holders. Set of two. 

Molded holders for lower suspension pivot pins. Set of four. 

Set of molded composite lower suspension pin holders. The suspension holders have a 0.75mm eccentric hole that lowers the rear roll center. Using the eccentric rear suspension holders will create more rear grip and at the same time increase steering.  

Set of nylon hubs includes: four eccentric hubs for differential ball-bearings, two non-eccentric hubs for layshaft ball-bearings. Eccentric hubs allow for tightening and loosening of front and rear drive belts. 

Molded clips for adjusting caster and wheelbase. Two sets of 4 clips. 

Ultimate assortment of set-up shims. You can use the shims for easy and accurate adjustment of:
- front and rear roll center
- front bump steer
- front and rear toe-in
- wheelbase  

Ultimate assortment of set-up shims. You can use the shims for easy and accurate adjustment of:
• front and rear roll center
• front bump steer
• front and rear toe-in
• wheelbase  

Molded rear short lower suspension arm for C-hub suspension. May be used on either left or right side. 

Molded rear short lower suspension arm for C-hub suspension. Hard rigidity. May be used on either left or right side. Engraved with "H" for easy identification. 

Ultra-Flex High-Performance Drive Belt
For top competition racing XRAY offers these specially modified high-performance drive belts. The belts are very thin and elastic as possible to create much more effective transmissions, save batteries and eliminate friction. The belt is specially modified - hand ground on a special machine so the belt is as thin as possible, but in such a way that it will still have long life.
"A must have item for serious racers."  

Specially modified high-performance 3mm-wide drive belt is 1mm narrower than original 4mm belt (#305441) for increased transmission efficiency. This belt is very thin and elastic as possible for an extremely effective transmission that saves batteries and eliminates friction. The belt is specially modified - hand ground on a special machine so the belt is as thin as possible, but in such a way that it will still have long life.

To fully enjoy the benefits from these high-performance belts, be sure all the transmission's ball-bearings are absolutely clean and there is no undue drag or friction. 

Central layshaft set for XRAY T1FK’05 includes CNC-machined hollow, ultra lightweight alu layshaft, precision-molded 20T pulleys, and all mounting hardware. 

CNC-machined hollow, ultra lightweight alu layshaft for XRAY T1FK’05. 

Precision-molded 20T layshaft pulleys for XRAY T1FK’05. Set of two. 

XRAY precision molded offset spur gear 78 tooth, 48 pitch. This spur gear has been strategically lightened to reduce rotating mass. 

XRAY precision molded offset spur gear 81 tooth, 48 pitch. This spur gear has been strategically lightened to reduce rotating mass. 

XRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been strategically lightened to reduce rotating mass. 

XRAY precision molded spur gear 87 tooth, 48 pitch. This spur gear has been strategically lightened to reduce rotating mass. 

XRAY precision molded spur gear 90 tooth, 48 pitch. This spur gear has been strategically lightened to reduce rotating mass. 

XRAY precision molded offset spur gear 104 tooth, 64 pitch. This spur gear has been strategically lightened to reduce rotating mass. 

XRAY precision molded offset spur gear 106 tooth, 64 pitch. This spur gear has been strategically lightened to reduce rotating mass. 

XRAY precision molded offset spur gear 108 tooth, 64 pitch. This spur gear has been strategically lightened to reduce rotating mass. 

XRAY precision molded offset spur gear 110 tooth, 64 pitch. This spur gear has been strategically lightened to reduce rotating mass. 

XRAY precision molded offset spur gear 112 tooth, 64 pitch. This spur gear has been strategically lightened to reduce rotating mass. 

XRAY precision molded offset spur gear 114 tooth, 64 pitch. This spur gear has been strategically lightened to reduce rotating mass. 

XRAY precision molded offset spur gear 116 tooth, 64 pitch. This spur gear has been strategically lightened to reduce rotating mass. 

XRAY precision molded offset spur gear 118 tooth, 64 pitch. This spur gear has been strategically lightened to reduce rotating mass. 

Rear lower (inner) spring steel pivot pins for XRAY T1FK’05. Hardened for very high durability and long life. Set of two. 

Set of shims for setting static wheelbase. Fits over rear lower pivot pins, servo saver, front one-way diff and other shims. 

M3x8 setscrew, hex drive. Set of 10 pieces. 

M4x8 setscrew, hex drive. Set of 10 pieces. 

M3x5 button-head machine screw, hex drive. Set of 10 pieces. 

M3x10 button-head machine screw, hex drive. Set of 10 pieces. 

M3x12 button-head machine screw, hex drive. Set of 10 pieces. 

M3x6 flat-head machine screw, silver colour, hex drive. Set of 10 pieces. 

New high-speed ball-bearings manufactured specially for XRAY. ID x OD x thickness (mm) = 5x9x3. Set of 2 pieces. 

New high-speed ball-bearings manufactured specially for XRAY. ID x OD x thickness (mm) = 6x10x3. Set of 2 pieces. 

New high-speed ball-bearings manufactured specially for XRAY. ID x OD x thickness (mm) = 10x15x4. Set of 2 pieces. 

5mm dia. E-clip. Set of 10 pieces. 

Polished chrome pin. Dia. x length = 2mm x 10mm. Set of 10 pieces.